String Pattern: 22×23 and 20×22 Are Different Rackets
A spec sheet will tell you the weight, the balance, the stiffness and the tension ceiling. It will often omit the string count, which is the one number that predicts how long a string lasts and how the frame feels on contact — before any of the others come into play.
For a buyer assembling a range, string pattern is also the cheapest way to create two genuinely different products from one mould. It is a design decision that costs the factory almost nothing and changes the customer’s experience completely.
What the numbers mean
The pattern is written mains by crosses. A 22×23 frame has twenty-two vertical strings and twenty-three horizontal ones; a 20×22 has fewer of both. The total is not the point — the spacing is. A denser bed means smaller gaps between strings, a firmer surface, and less movement at impact.
That translates into three effects that matter commercially. Denser beds last longer because the string moves less and wears less at the grommets. Denser beds produce less power at the same tension because the bed deforms less. Denser beds feel firmer and give more feedback, which some players want and others find harsh.

Why it gets left off
String pattern is invisible in a photograph and hard to describe in a listing, so it drops out of the specification sheet and then out of the conversation. The problem is that the customer’s complaint is described in exactly those terms without naming them: “this one feels dead”, “this one breaks string every two weeks”, “this one is too powerful”.
All three are pattern effects. A shop trying to solve them with string choice is treating a symptom, and the fix will not hold.
Open patterns and string breakage
An open pattern moves more at impact, which increases the sawing action at each grommet and shortens string life. That is a real trade-off rather than a defect: the same movement is what produces the livelier response and the easier access to power that an open pattern is chosen for.
This is where the pattern should be matched to the customer, not to the price. A junior or a beginner who hits off-centre will break string on an open pattern faster than on a dense one, and the resulting cost — restrings per season — is a bigger number than the price difference between the two frames.

Grommets and the pattern together
The grommet is the interface between string and frame, and its condition interacts with the pattern. A dense bed with worn grommets cuts string as surely as an open bed with new ones; the two are usually discussed separately and should not be. When a frame comes back with repeat breakage at the same point, the pattern is part of the diagnosis, and so is the grommet at that point.
What to put on the specification
- String count, mains by crosses, stated explicitly.
- Recommended tension range for that pattern, not just the frame ceiling.
- Grommet specification and whether the set is replaceable.
- Head size, since pattern density is a function of count over area.
- Which string the frame was validated with, if any.
Two frames from one mould with different patterns give a distributor a range with a real internal logic. The CC6.0 and the STORM 90 can be presented as a choice between response and durability rather than as two price points — and the customer who understands that choice comes back to the same shop, because the shop explained something true.
It also simplifies returns. When breakage is reported, the grading starts from a known pattern and a known tension range, which is the difference between a diagnosis and a guess.
Grommet strips and the pattern together
Grommets are sold as strips or as single pieces, and the specification that matters is the bore and the length rather than the appearance. A grommet that is too short lets the string sit against the frame; one that is too long lifts the string off the bed and changes the angle at the edge. Both failures appear as string breakage rather than as a grommet problem.
Keep a set per model in the shop. It is the cheapest way to make a repeat breakage diagnosable, because the shop can replace the strip and see whether the failure moves.
Why dense patterns need more attention
A denser bed means more contact points per square centimetre, so the same string passes through more grommets and each one carries slightly less movement. Less movement means less cooling, and the wear concentrates rather than spreads. That is why a dense frame with worn grommets fails faster than an open one with the same wear.
Common mistakes on this specification
- Omitting string count from the specification entirely.
- Comparing two frames by head size while ignoring the count.
- Recommending tension without reference to the pattern.
- Treating repeat breakage as a string problem by default.
- Shipping frames without a replacement grommet set available.
Four of the five can be fixed by one line on the spec sheet and one spare set in the shop.