0.60 mm Overgrip: The Thickness the Market Already Chose
OVERGRIP · TECHNICAL NOTE
Overgrip thickness is one of the few numbers in a racket catalogue a player can feel immediately, and almost the only one where the market has already settled on an answer without anyone announcing it. The best-selling overgrip in racket sports is 0.60 mm thick, and it has been since 1987. If your product is 0.80 mm and you are up against that, you are not competing on feel. You are competing on a different handle size.
01 · THE BENCHMARK
One thickness has already won
Yonex publishes AC102 Super Grap as 25 mm wide, 1,200 mm long, 0.60 mm thick, polyurethane. The model has been on sale since 1987, the company calls it its best-selling overgrip, and it describes the volume sold as enough to wrap around the world five times. That last part is marketing copy. The specification behind it is a fact on a public page, and it is the number most club players in Europe and Asia have already held in their hand.
Around it, the market runs from roughly 0.40 mm to 0.90 mm. Below 0.50 mm the grip is a feel product: maximum bevel definition, short life. Above 0.80 mm it stops being a surface and starts being a handle modification. 0.60 mm is where those two curves cross: thin enough to keep the octagon, thick enough to survive more than a few sessions of sweat.
02 · THE GEOMETRY
What 0.60 mm does to a handle

Wrapping a convex section in a uniform layer of thickness t adds 2πt to the circumference. The shape does not matter: an octagon and a circle gain the same perimeter from the same layer. At 0.60 mm that is 3.77 mm. One tennis grip size is 1/8 inch, or 3.175 mm, so a single 0.60 mm wrap is geometrically about 1.2 grip sizes.
| Thickness | Added circumference | Grip sizes (1/8 in) |
|---|---|---|
| 0.43 mm | 2.70 mm | 0.85 |
| 0.50 mm | 3.14 mm | 0.99 |
| 0.60 mm | 3.77 mm | 1.19 |
| 0.65 mm | 4.08 mm | 1.29 |
| 0.75 mm | 4.71 mm | 1.48 |
| 0.80 mm | 5.03 mm | 1.58 |
Circumference added = 2π × thickness, assuming a uniform uncompressed layer. Grip size step = 1/8 in = 3.175 mm.
Two things follow. If a player’s handle already fits, a 0.60 mm overgrip takes it a full size up, which is why the standard advice is to buy one size small if you always wrap. And if you are building a range, the thickness ladder is a fit ladder rather than a price ladder: 0.60 and 0.65 for players protecting the bevel, 0.80 and above for players building a handle up.
A thin overgrip does not make the handle smaller. It makes the handle grow more slowly, which is a different specification.
03 · THE HALF-SIZE RULE
Why both numbers are right
Nearly every buying guide says one overgrip adds about 1/16 inch, or 1.6 mm, which is half a grip size. The arithmetic above says 3.8 mm. Both numbers are in circulation because they measure different things.
The 1.6 mm figure is what players measure after wrapping. The 3.8 mm figure is what an uncompressed layer of that thickness has to add. The gap is made of three real effects: the strip is stretched when it is pulled, so it thins; it is wrapped with overlap, and the overlap compresses the layer below; and the listed thickness is measured on a flat, unstretched strip rather than on a handle.
The practical consequence for a buyer is that the same 0.60 mm grip feels like half a size to one player and a full size to another, depending on how hard they pull it. That is not a quality problem, it is the specification behaving as designed. It does mean that a claim like “adds half a size” should not go on a pack without the word approximately somewhere near it.
04 · THE PICKLEBALL CASE
Why pickleball got to 0.60 first
Most adult pickleball paddles ship at 4.25 inches of circumference, and 4.0 to 4.5 inches covers nearly every hand. The standard fitting advice in that sport is to buy slightly small and build up, because you can add material to a handle and you cannot take it away.
That advice only works if each layer is small. Pickleball retailers and paddle makers put one overgrip at about 1/16 inch of added circumference, so one layer moves a 4.25 inch handle to roughly 4.31, and two layers take it most of the way to 4.375. A 0.80 mm wrap adds about 5 mm in one pass, which is a full size, and it leaves a player who wanted a fine adjustment holding a handle at the top of the range.
There is a second reason. Pickleball is played outdoors, in the conditions where a tacky PU surface softens, and the handle is held with more wrist action at the kitchen line than a tennis racket is held at the baseline. A thick, soft layer costs mobility there. Thin does not solve sweat, but it stops the grip itself from becoming the reason a dink pops up.
05 · THE ORDER
What 0.60 mm costs you commercially
Thickness is a coating decision, and coating is set per run. Two consequences for anyone placing an order:
White, black and green are three runs, not one order split three ways, because the pigment goes into the coating. It is also why laboratory testing is charged per colour: a different colour is a different homogeneous material.
1,200 mm is the reference length and covers a standard handle with margin. 1,100 mm is the same grip cut shorter. Neither is better, they are two answers to two packing lists.
06 · SPECIFY IT
What to put in the brief
- Thickness in millimetres, and whether the tolerance applies to the film or to the finished grip.
- Length in millimetres, because 1,100 and 1,200 are both standard and not interchangeable inside the same pack.
- Surface: tacky, dry, buffed grain, perforated or keel. Tacky and dry are not quality grades, they are two answers to the same sweat problem.
- Colour count, stated as a number. It sets both the minimum order and the test bill.
- Packing format. Single piece, three-pack and roll are separate runs, quoted separately.
- Whether the backing film carries your brand, which brings its own print setup.
The thickness ladder and the twenty-one models currently in production, 0.60 mm to 1.9 mm, are laid out on the grip and overgrip OEM page. If you want to see what a given thickness does to a specific handle, the grip size calculator runs the 2πt arithmetic for you. And if the constraint you are working against is length rather than thickness, the winding geometry note covers why 1,100 mm is tighter than it looks.